Secondly, in addition to the rate of force development, the size of the force itself produces a negative feedback effect on vertical impulse, because higher forces lead to faster accelerations, which in turn reduce the time spent producing force before take-off. This is *partly* why drop jumps tend to involve higher forces, shorter ground contact times, and yet similar jump heights to countermovement jumps.
Dunking is a dramatic, crowd-pleasing offensive move. Many times, a rousing dunk can turn that mysterious factor, momentum, right around in your favor. Clearly, dunking is easier if you're tall and can palm the ball with one hand, but there have been relatively short players who couldn't palm the ball who worked hard enough to be able to dunk. If you are considering adding the dunk shot to your repertoire, follow these steps:
Bought this as a training aid for my track team and so far no complaints it really does what i need it to do. I would recommend you come up with some drills when you buy this because if you improperly use it could injure the athlete you can not wing it with this. i like to you use it for warms ups or for specific strength training for my better athletes.
these shocks make a big difference in handling and ride on the2015 4wd F250. This will make the suspension work rather than the whole vehicle simply shuddering up and down over small bumps and holes in the road. Tires stay in contact with road, suspension moves, you and the seat stay still, what a concept! OEM shocks don't even move once compressed, pityful. You will need an 18 mm wrench or socket for lower shock mount bolts and a 21 mm open end, box end or deep socket for the top mount nut and a 20mm or adjustable wrench for the shaft bolt on the top mount. Once the old shocks are off, you need a 19mm open end or socket for the Bilstein top mount nut and you hold the shaft from moving with a hex key, in my experience I didn't really need that but you may want to. Check the top of the shaft you'll see a hex hole up there, seems like it was a 6mm but don't hold me to that. Forget any jacking, removing tires, etc to do this it isn't necessary, and much safer with wheels on the ground while you are under there. If you need some space I drove the wheel I was working on over a 2x12 and that gave me a little height to work with. I wasn't in the mood to fool with jacks, jack stands and all that. No need to. Just crank the steering wheel over away from the side you are working on and you'll have plenty of room. The only issue is after attaching the lower shock mounts using the OEM 18mm bolt/nut, you need to compress the shock about 3" to get it into the upper mounting hole. I used a common tie down racheting strap for this job. I hooked one hook to the chassis right under the lower shock mount bracket on the truck and after adjusting the strap length I put the upper hook around the top shock rubber grommet and washer (lower one already installed now, put upper ones on after shock is in place, of course). At this point you just crank the rachet on the strap until the shock compresses a few inches and shove the shaft under the mounting hole, release the rachet and up pops the shock into place. Put on upper grommet and washer, tighten 19mm nut and presto! IF the shaft turns while you tighten this nut hold the shaft still with the hex key mentioned earlier. Your truck is now a better place to be. Also just tighten upper nut until the grommet fills or slightly goes outside the washer, don't crank it down and flatten the grommet. If you aren't sure look at the OEM arrangement for an idea on how tight to go with that nut. Happy motoring !!
Copyright © 2019 HubPages Inc. and respective owners. Other product and company names shown may be trademarks of their respective owners. HubPages® is a registered Service Mark of HubPages, Inc. HubPages and Hubbers (authors) may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others.
In fact, if you are a very short player and can barely reach the net when you jump you should probably put the dream of dunking the ball out of your mind. Better to spend time working on your layups and ball-handling skills. You can still lift weights and do all the other things to increase your vertical leap, and you can still be a very effective player.
Hi I'm 14 years old and 6 foot 4 I can dunk but not really good like I need more air so that I can dunk better and I'm trying to get my vertical jump up to 5 feet my vertical you probably will say that's crazy but it's possible a really love it that a 13 year old can dunk but I want to do something amazing and that is to be better that micheal Jordan and I will succeed thank you so much hope you see me in the NBA .
Important Update! – I have been receiving a few emails/comments on players tracking their jump during the course of their program. Please understand that what you are doing when completing a jump program is breaking down the muscle. You aren’t going to see improvements mid-week because the muscle hasn’t healed properly. That’s why I suggest only checking how much you’ve improved at the end of each rest week. Rest is just as important as the routine.