these shocks make a big difference in handling and ride on the2015 4wd F250. This will make the suspension work rather than the whole vehicle simply shuddering up and down over small bumps and holes in the road. Tires stay in contact with road, suspension moves, you and the seat stay still, what a concept! OEM shocks don't even move once compressed, pityful. You will need an 18 mm wrench or socket for lower shock mount bolts and a 21 mm open end, box end or deep socket for the top mount nut and a 20mm or adjustable wrench for the shaft bolt on the top mount. Once the old shocks are off, you need a 19mm open end or socket for the Bilstein top mount nut and you hold the shaft from moving with a hex key, in my experience I didn't really need that but you may want to. Check the top of the shaft you'll see a hex hole up there, seems like it was a 6mm but don't hold me to that. Forget any jacking, removing tires, etc to do this it isn't necessary, and much safer with wheels on the ground while you are under there. If you need some space I drove the wheel I was working on over a 2x12 and that gave me a little height to work with. I wasn't in the mood to fool with jacks, jack stands and all that. No need to. Just crank the steering wheel over away from the side you are working on and you'll have plenty of room. The only issue is after attaching the lower shock mounts using the OEM 18mm bolt/nut, you need to compress the shock about 3" to get it into the upper mounting hole. I used a common tie down racheting strap for this job. I hooked one hook to the chassis right under the lower shock mount bracket on the truck and after adjusting the strap length I put the upper hook around the top shock rubber grommet and washer (lower one already installed now, put upper ones on after shock is in place, of course). At this point you just crank the rachet on the strap until the shock compresses a few inches and shove the shaft under the mounting hole, release the rachet and up pops the shock into place. Put on upper grommet and washer, tighten 19mm nut and presto! IF the shaft turns while you tighten this nut hold the shaft still with the hex key mentioned earlier. Your truck is now a better place to be. Also just tighten upper nut until the grommet fills or slightly goes outside the washer, don't crank it down and flatten the grommet. If you aren't sure look at the OEM arrangement for an idea on how tight to go with that nut. Happy motoring !!
No, I think there’s a practical aspect to that. It’s hard to grip a basketball. I mean, that’s another physical challenge. I have pretty small hands, and one thing I had to train myself to do, which I couldn’t do at the start of this project, is palm a basketball. So that involved fingertip push-ups, to get the tips of your fingers much stronger. It involves, while hanging out and watching television, trying to palm a basketball for as long as you can. You want to get into a quick, full sprint, and you want to be able to grip the basketball as you go up to jam it. So doing those things can be a challenge. That’s partly what’s behind people doing the alley-oop-type things or throwing it up off the backboard. In some cases, they simply can’t grip the ball on the way to the hoop, so their solution is to throw it in the air, catch it, and try to bring it down.
Use a smaller ball. It's much easier, when you're first starting out, to try dunking with a smaller ball. You'll be able to palm it more easily and control your approach, making the maneuver more satisfying and your practice closer to the real thing. Continue dribbling and shooting exercises with the appropriate-sized ball so you're not getting too used to the "wrong" size, but keep a small ball around for your sick dunks.[1]

Ok I just turned 18 2 months ago and I'm 6,2 and weigh about 155 and I'm very athlectic I've played basketball ever since 3rd grade so I'm very familiar with tecniques and fundamentals I don't play as much as I used to but I can still get rim on my thumb no prob but can't dunk.what can I do bc I wanna jam on my bro. Also being noted that I've dunked about 2 Times but were sloppy plz help
Many models have been constructed to identify the most important muscles in the vertical jump, with some conflicting results. Some have suggested that movement is governed by the gluteus maximus and quadriceps, while others have proposed that the hamstrings, quadriceps, and calf muscles are key. Importantly, no model has yet explored the role of the adductor magnus, which is the primary hip extensor in the barbell squat. This is relevant, as many studies have found that the squat is an ideal exercise for improving jump height, and maximum back squat strength is closely associated with vertical jump performance among athletes.

Strength exercises include slow, controlled movements like squats, lunges, and weighted step-ups.  Power exercises require explosive, quick moves like those needed for plyometrics and power cleans. Plyometrics are explosive bounding, hopping and jumping drills that blend strength and speed. Finally, practicing maximum vertical jump will increase vertical jump.
Hi im Deontay i been trying 2 dunk ever since 7th grade and i know i been improveing since 7th grade i could touch the bottom of the backboard and i guest i was 5'6 or 5'7 at the end of the 8th grade i started exercising by having a 150 pound bag of cement on my shoulders and started squats and i try 2 15 wit a extra 5 at ever exercise i do but i still c very little effects so when went 2 my last day of school i could touch rim easily but the rim was about 8 foot and i was 5'9 now im a freshmen at my high school and i grip 10 foot rim wit my fingers not wit my hands but wit my fingers and im at 5'10 and im only 15 and i think my growing sprout is kicking in but anyway i want 2 know how can i get the ball over the rim and pound it in like d.rose king james and blake griffin i could grip the ball all i need 2 know is how 2 jump high enough 2 have that ball above the rim and pound it in will u please help

In the tradition of New Year’s resolutions and the like, you can give yourself a year. I certainly didn’t want to give myself more than a year, because after a year I knew I would grow tired of it, and my body would start to get quite unhappy with me. But I would recommend to someone that they give it a go for at least six months. It’s also a way of just getting yourself in fantastic shape. I mean, trying to dunk a basketball in itself is awesome. It’s really great to be able to dunk a basketball, to get yourself higher up than you thought possible. But the process of getting yourself in that kind of position is itself rewarding.


After warming up, I proceeded to slam Jeff’s best lobs off the back rim at least 10 times, watching these missed dunks rebound high over the lane and land somewhere near the three-point line. It’s tough to express how difficult it was to pack up and walk away from the court on such days, to listen to my body when it told me it had reached the point of diminishing returns. To come up with yet another way to tell the wife: No, not today, Sugar. But I came reeeally close.
Jumping Rope – A skipping rope is the only piece of equipment involved in the program. If you don’t have one a piece of rope will do just fine. If you don’t have a piece of rope either jumping up and down on the spot without much bending in the knees will achieve a similar result. Jumping rope involves holding a rope with both hands and swinging it around your body continuously.
×