All data were analyzed according to the intention-to-treat principle. Differences in the primary outcome were analyzed with the use of an unadjusted chi-square test. Results are presented as absolute and relative risks and 95% confidence intervals. Kaplan–Meier curves for estimated survival were compared with the use of a log-rank test. A Cox proportional-hazards regression model was used to evaluate the influence of potential confounding factors on the outcome (factors were selected if the P value in the univariate analysis was <0.20).

Results: You need a 0 Inch vertical leap to touch the rim and 6 Inch leap to dunk considering that you have to jump about 6 inches over the rim to dunk. To accomplish that you have to leave the ground at a speed of 1.73 m/s vertically no matter how much you weigh. You need a force of 0 Newtons against the ground based on your weight to reach that speed assuming you bent your knees at an angle of 60 degrees. The force depends on how much you bent your knees. Check side bar.

Using only a lifting (concentric) phase for strength training exercises could also be more effective for improving vertical jump height than traditional, stretch-shortening cycle exercises under load, for two reasons. Firstly, using only a lifting phase involves faster rate of force development through higher rate coding, and this may increase high-velocity strength more over the long-term. Secondly, doing stretch-shortening cycle exercises under load *might* cause the tendons to increase stiffness to a greater extent. This would make the muscle lengthen more in the countermovement phase of a jump, and thereby reduce muscle force for a given countermovement depth.
I paid a lot of money for a vertical leap training system in the past that was a total scam. The red flags were everywhere, but I overlooked them because I was so eager to train and get results. That's why I was tentative when I first found out about TTS and Coach Cascio. Not wanting to be ripped off again, I decided to thouroughly look through his website. I was surprised to see that he actually communicated with customers via social media and actually shared useful information and excercises for free with email, Youtube, and now this book. This honest approach made me feel confortable and so I decided to give his program a shot. Thanks a lot for working hard for us, Jack.
Plyometrics is the best known of the jumping development exercise programs. Plyometrics training emphasizes speed and explosive movement, and a plyometrics program will typically consist of a series of bounding, hopping, and jumping drills. The object of a plyometrics program is to perform the exercises at maximum intensity. For this reason, plyometrics training must be approached with caution, and the athlete must progress slowly from one level to the next to reduce the risk of injury. Proper rest intervals must also be incorporated in to plyometrics training, as the exercises are intended to place significant stress on the target muscle groups.

Our Keep-It™ guarantee is valid for the first-time purchase of a formula, and redeemable up to three months (90 days) after the purchase date. Multiple bottles, foods, apparel and gear do not fall under this guarantee, however, they may be applicable for return. Fitness equipment, personal care products, knowledge purchases, and DVDs are not eligible for return or refund. For more information and a full list of products that qualify, visit our Keep-It™ page. Further details can be found on our Refund Policy support page.
Independent 6'2" North American athlete Eric Bishop introduced a dunk entitled the 'Paint Job'. The title is in reference to the key on a basketball court, often known as 'paint' in common parlance.[36] Approaching along the baseline with a running dribble, Bishop jumped with one-foot at the border of the key, dunked with one-hand while gliding over the key and landed just beyond the border on the side opposite his take-off—a 16-foot flight.
A second, more efficient and correct method is to use an infrared laser placed at ground level. When an athlete jumps and breaks the plane of the laser with his/her hand, the height at which this occurs is measured. Devices based on United States Patent 5031903, "A vertical jump testing device comprising a plurality of vertically arranged measuring elements each pivotally mounted..." are also common. These devices are used at the highest levels of collegiate and professional performance testing. They are composed of several (roughly 70) 14-inch prongs placed 0.5 inches apart vertically. An athlete will then leap vertically (no running start or step) and make contact with the retractable prongs to mark their leaping ability. This device is used each year at the NFL scouting combine.